Linux version 2.6.25-gentoo-r7 (root@dns) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #1 SMP Wed Oct 1 03:30:59 CDT 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 0000000000100000 - 00000000cfeb2000 (usable)
BIOS-e820: 00000000cfeb2000 - 00000000cfec8000 (reserved)
BIOS-e820: 00000000cfec8000 - 00000000cfee7c00 (ACPI data)
BIOS-e820: 00000000cfee7c00 - 00000000d0000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fe000000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
Warning only 4GB will be used.
Use a HIGHMEM64G enabled kernel.
3200MB HIGHMEM available.
896MB LOWMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at [c00fe710] 000fe710
Entering add_active_range(0, 0, 1048576) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 1048576
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 1048576
On node 0 totalpages: 1048576
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 6400 pages used for memmap
HighMem zone: 812800 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
DMI 2.5 present.
Using APIC driver default
ACPI: RSDP 000F2980, 0024 (r2 DELL )
ACPI: XSDT 000F2A08, 0094 (r1 DELL PE_SC3 1 DELL 1)
ACPI: FACP 000F2B20, 00F4 (r3 DELL PE_SC3 1 DELL 1)
ACPI: DSDT CFEC8000, 2545 (r1 DELL PE_SC3 1 INTL 20050624)
ACPI: FACS CFEE7C00, 0040
ACPI: APIC 000F2C14, 0072 (r1 DELL PE_SC3 1 DELL 1)
ACPI: SPCR 000F2C93, 0050 (r1 DELL PE_SC3 1 DELL 1)
ACPI: HPET 000F2CE3, 0038 (r1 DELL PE_SC3 1 DELL 1)
ACPI: MCFG 000F2D1B, 003C (r1 DELL PE_SC3 1 DELL 1)
ACPI: WD__ 000F2D57, 0134 (r1 DELL PE_SC3 1 DELL 1)
ACPI: SLIC 000F2E8B, 0024 (r1 DELL PE_SC3 1 DELL 1)
ACPI: ERST CFECB114, 0210 (r1 DELL PE_SC3 1 DELL 1)
ACPI: HEST CFECB324, 027C (r1 DELL PE_SC3 1 DELL 1)
ACPI: BERT CFECAF94, 0030 (r1 DELL PE_SC3 1 DELL 1)
ACPI: EINJ CFECAFC4, 0150 (r1 DELL PE_SC3 1 DELL 1)
ACPI: SSDT CFECA545, 032C (r1 DELL PE_SC3 11 INTL 20050624)
ACPI: SSDT CFECA9BB, 032C (r1 DELL PE_SC3 11 INTL 20050624)
ACPI: SSDT CFECAE31, 0162 (r1 DELL PE_SC3 10 INTL 20050624)
ACPI: DMI detected: Dell PE R200
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x13] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a301 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at d1000000 (gap: d0000000:10000000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1040384
Kernel command line: root=/dev/sda3
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2400.152 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3366616k/4194304k available (2596k kernel code, 38716k reserved, 1359k data, 248k init, 2489032k highmem)
virtual kernel memory layout:
fixmap : 0xffe14000 - 0xfffff000 (1964 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc04e4000 - 0xc0522000 ( 248 kB)
.data : 0xc038921a - 0xc04dd05c (1359 kB)
.text : 0xc0100000 - 0xc038921a (2596 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
hpet clockevent registered
Calibrating delay using timer specific routine.. 4803.80 BogoMIPS (lpj=9607610)
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 263 Objects with 33 Devices 104 Methods 8 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 5 Objects with 0 Devices 3 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0003) - 5 Objects with 0 Devices 3 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0004) - 13 Objects with 0 Devices 4 Methods 0 Regions
tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable : Transition to ACPI mode successful
CPU0: Intel(R) Core(TM)2 Duo CPU E4600 @ 2.40GHz stepping 0d
Booting processor 1/1 ip 4000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4800.16 BogoMIPS (lpj=9600334)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 Duo CPU E4600 @ 2.40GHz stepping 0d
Total of 2 processors activated (9603.97 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
net_namespace: 244 bytes
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1
Setting up standard PCI resources
evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 3F [_GPE] 8 regs on int 0x9
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 1 Wake, Enabled 1 Runtime GPEs in this block
ACPI: EC: Look up EC in DSDT
Completing Region/Field/Buffer/Package initialization:..........................
Initialized 5/8 Regions 0/0 Fields 10/10 Buffers 11/12 Packages (295 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:<5>ACPI: BIOS _OSI(Linux) query ignored via DMI
.
Executed 1 _INI methods requiring 0 _STA executions (examined 39 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0880-08bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBE0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBE4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBE5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 *6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 64-bit timers, 14318180 Hz
system 00:0a: ioport range 0x800-0x87f has been reserved
system 00:0a: ioport range 0x880-0x8bf has been reserved
system 00:0a: ioport range 0x8c0-0x8df has been reserved
system 00:0a: ioport range 0x8e0-0x8e3 has been reserved
system 00:0a: ioport range 0x900-0x900 has been reserved
system 00:0a: ioport range 0xc00-0xc0f has been reserved
system 00:0a: ioport range 0xc10-0xc1f has been reserved
system 00:0a: ioport range 0xca0-0xca7 has been reserved
system 00:0a: ioport range 0xca9-0xcab has been reserved
system 00:0a: ioport range 0xcad-0xcaf has been reserved
system 00:0a: ioport range 0xc20-0xc3f has been reserved
system 00:0b: ioport range 0xca8-0xca8 has been reserved
system 00:0b: ioport range 0xcac-0xcac has been reserved
system 00:0c: iomem range 0xe0000000-0xefffffff could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
IO window: e000-efff
MEM window: 0xdfb00000-0xdfcfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.4
IO window: disabled.
MEM window: 0xdfd00000-0xdfdfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.5
IO window: disabled.
MEM window: 0xdfe00000-0xdfefffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: d000-dfff
MEM window: 0xdff00000-0xdfffffff
PREFETCH window: 0x00000000d0000000-0x00000000d7ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.4 to 64
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
IA-32 Microcode Update Driver: v1.14a
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:05:05.0: Boot video device
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.103
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: ACPI0007:01 is registered as cooling_device1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial 00:07: activated
00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
floppy0: no floppy controllers found
brd: module loaded
loop: module loaded
console [netcon0] enabled
netconsole: network logging started
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
megasas: 00.00.03.16-rc1 Thu. Nov. 07 10:09:32 PDT 2007
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ata_piix 0000:00:1f.2: version 2.12
ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 23 (level, low) -> IRQ 23
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0xcc30 ctl 0xcc28 bmdma 0xcc40 irq 23
ata2: SATA max UDMA/133 cmd 0xcc38 ctl 0xcc2c bmdma 0xcc48 irq 23
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.01: ATAPI: TEAC DVD-ROM DV28SV, D.0E, max UDMA/100
ata1.01: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 0)
scsi 0:0:1:0: CD-ROM TEAC DVD-ROM DV28SV D.0E PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:1:0: Attached scsi CD-ROM sr0
sr 0:0:1:0: Attached scsi generic sg0 type 5
Fusion MPT base driver 3.04.06
Copyright (c) 1999-2007 LSI Corporation
Fusion MPT SPI Host driver 3.04.06
Fusion MPT FC Host driver 3.04.06
Fusion MPT SAS Host driver 3.04.06
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
mptbase: ioc0: Initiating bringup
ioc0: LSISAS1068E B3: Capabilities={Initiator}
PCI: Setting latency timer of device 0000:02:00.0 to 64
scsi2 : ioc0: LSISAS1068E B3, FwRev=00143000h, Ports=1, MaxQ=511, IRQ=16
scsi 2:0:0:0: Direct-Access ATA WDC WD2500YS-18S 6C07 PQ: 0 ANSI: 5
scsi 2:0:0:0: Attached scsi generic sg1 type 0
scsi 2:0:1:0: Direct-Access ATA WDC WD2500YS-18S 6C07 PQ: 0 ANSI: 5
scsi 2:0:1:0: Attached scsi generic sg2 type 0
scsi 2:1:0:0: Direct-Access Dell VIRTUAL DISK 1028 PQ: 0 ANSI: 5
sd 2:1:0:0: [sda] 486326272 512-byte hardware sectors (248999 MB)
sd 2:1:0:0: [sda] Write Protect is off
sd 2:1:0:0: [sda] Mode Sense: 03 00 00 08
sd 2:1:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:1:0:0: [sda] 486326272 512-byte hardware sectors (248999 MB)
sd 2:1:0:0: [sda] Write Protect is off
sd 2:1:0:0: [sda] Mode Sense: 03 00 00 08
sd 2:1:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 2:1:0:0: [sda] Attached SCSI disk
sd 2:1:0:0: Attached scsi generic sg3 type 0
Fusion MPT misc device (ioctl) driver 3.04.06
mptctl: Registered with Fusion MPT base driver
mptctl: /dev/mptctl @ (major,minor=10,220)
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xdfaffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000cc60
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000cc80
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 21, io base 0x0000cca0
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-5: new high speed USB device using ehci_hcd and address 2
usb 1-5: configuration #1 chosen from 1 choice
hub 1-5:1.0: USB hub found
hub 1-5:1.0: 4 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
oprofile: using NMI interrupt.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Using IPI No-Shortcut mode
input: ImExPS/2 Generic Explorer Mouse as /class/input/input2
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 248k freed
EXT3 FS on sda3, internal journal
tg3.c:v3.91 (April 18, 2008)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:03:00.0 to 64
eth0: Tigon3 [partno(BCM95721) rev 4201 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:21:9b:fa:ec:39
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:04:00.0 to 64
eth1: Tigon3 [partno(BCM95721) rev 4201 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:21:9b:fa:ec:3a
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[76180000] dma_mask[64-bit]
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
Adding 31254448k swap on /dev/sda2. Priority:-1 extents:1 across:31254448k